Doran 360RV Bedienungsanleitung

Manufacturing LLC360RVPLEASE READ THIS MANUAL CAREFULLY BEFOREUSING THIS PRODUCT.USER MANUALThe DORAN 360RV is designed solely to monitor tire pressur

8188 PSI,depending on your needs. Each wheel position can be set with a different baseline air pressure if this is what is needed. The monitor has b

9NOTE: To skip this section and go directly to Programming the Unit of Measure section, just press the PROG button briefly 1 time. The display should

10SET button for 3 seconds until the monitor beeps twice and the display flashes twice. The display is shown like Figure 2-14.4. To adjust the hour

NOTE: To enter directly into this program mode you will need to press the button for 5 seconds until the is displayed. Then press the button again

12E. Delete Sensor LocationThis step is only used when a sensor is to be removed from the memory of the monitor. This would be used to remove a senso

133. If you have additional sensors that need to be deleted repeat the steps until all required sensors are deleted. If you need to program delet

143. Pressing the PROG button briefly will rotate you back through the different programming modes. If you are done with the programming operatio

Keep in mind that tire pressures will increase as you drive. When tires are in motion, the sidewalls are under stress carrying the load of the vehicl

III. INSTALLING THE SENSORS ON THE VEHICLE164. If the monitor continues to search for a sensor after 10 minutes it is possible that the sensor may

IV. ALARM MODES171. FIRST STAGE ALARM FOR 12.5% LOW AIR PRESSURE: On a first level low pressure alarm the monitor will alarm at 12.5% below th

TABLE OF CONTENTSI. Introduction to the Doran 360RV------------------------------------------------------------------------------------- Componen

18IV. ALARM MODESthe words LOW PRESSURE until the problem is corrected. If the alarm comes on and the FAST LEAK icon appears (see figure 4-2), this m

V. NORMAL MODE ACCESSORY FUNCTIONS191. Drop and Hook FeatureThis feature allows the operator of the vehicle to drop the monitoring of either the front

V. NORMAL MODE ACCESSORY FUNCTIONS2. System Reset FunctionThe monitor can be reset to the factory defaults in one easy step. This will erase all of t

21V. NORMAL MODE ACCESSORY FUNCTIONSThe display will show as follows:Figure 6-2 Actual pressure for the alarmFigure 6-3 d07 is for the 7th month o

22VI. FAQS AND TIPS1. FREQUENTLY ASKED QUESTIONSDOES THE MONITOR NEED TO BE POWERED BY A LIGHTER ACCESSORY?No. In fact you will loose some of the ben

23CAN THE MONITOR BE USED INDEPENDENTLY ON FRONT OR TOWVEHICLE? Yes see Drop and Hook Instruction PAGE 19.CAN I STORE MY VEHICLE LONG TERM WITH THE

24HOW DO I DELETE A SENSOR? See page 12 for full details on sensor deletion.WHAT SHOULD BE DONE IF A LOW PRESSURE ALERT IS SOUNDED? Immediately pull

25MY SENSOR WAS BLOWN OFF, (BLOWOUT) WITH NO ALERT GIVEN, WHY? Instant tire failure is rare in comparison to the more common failure caused by gradual

263. LIMITED WARRANTYTWO-YEAR LIMITED WARRANTY: Subject to the limitations and exclusions set forth in this Limited Warranty, the DORAN 360RV is warr

27PROCEDURE: Products determined to be defective within the terms of this Limited Warranty should be returned to Doran Mfg. LLC, transportation prepa

I. INTRODUCTION The Doran 360RV is a full-time wireless electronic tire pressure monitoring system (TPMS) designed to monitor and display tire pressur

284. SPECIFICATIONSSensor Transmit RangeOperating FrequencyOperating Temperature RangeStorage Temperature RangeSensor WeightSensor DimensionsSensor Ba

VII. OPTIONAL ACCESSORIESNOTES: 2007 - All Rights ReservedDORAN MANUFACTURING LLC2851 Massachusetts AvenueCincinnati, OH 45225Tel: 866-816-7233

#3672 Rev 1

I. INTRODUCTION 2 Tires can fail for other reasons besides low pressure or overloading. Always be on the alert for any other tire problems a

II. SETUP AND INSTALLATION1. Monitor Installation The 360RV gives the user multiple options for mounting the monitor for viewing. You have the option

4 The monitor is fused internally, however some installers would still prefer to install an inline fuse for precautions. We suggest an option

5II. SETUP AND INSTALLATIONA. Programming the Sensor Location1. Be sure that the power is on. The first time the monitor is switched on; the display

64. Using the arrow keys select the first tire position that you want to program. The selected wheel location will be solid. The other wheel pos

10. Once you have completed the sensor programming sequence for all tires, press the PROG button momentarily to move to the next step, this will